SAE 100R1 high tensile steel wire braided medium pressure hose

SAE 100R1AT single steel wire braided hose is a typical medium pressure hydraulic hose and strongly recommended for hydraulic lines or general industrial system. High tensile strength steel wire reinforcement makes SAE 100R1 hose support higher pressure than common steel wire does.

Apart from standard SAE 100R1 hose, high temp and high abrasion hydraulic hoses are supplied. They are designed to meet higher standard.

Option One (high abrasion):
Tube: Excellent oil resistant Nitrile;
Reinforcement: single high tensile strength steel wire braid;
Cover: modified nitrile;
Max working pressure: 3625 psi (at 3/16");
Working temperature: -40 to +100°C (-40 to +212°F);
Inside diameter: 3/16" to 2";
Pressure grating: 3045psi (at 3/16", type AT) and 3625 psi (at 3/16", type S);
Safety factor: 4:1;
Pressure grade: medium.

Option Two (high temp):
Tube: Excellent oil resistant Nitrile;
Reinforcement: single high tensile strength steel wire braid;
Cover: abrasion and weather resistant Chlorosulphonated Polyethylene (CSM);
Max working pressure: 3625 psi (at 3/16”);
Working temperature: -40 to +100°C (-40 to +212°F) or as ordered;
Inside diameter: 3/16” to 2”;
Pressure grating: 3045psi (at 3/16”, type AT) and 3625 psi (at 3/16”, type S);
Safety factor: 4:1;
Pressure grating: medium.

Remarks: Hoses meet or exceed SAE 100R1 are manufactured. You kindly send us your specified technical data if you can't find the one from the table below.

SAE 100R1AT Medium Pressure Hydraulic Hose
Part No.	Metric Size	Inch Size	SAE Dash Size	Hose I.D.		Reinforcement		Max. Working Pressure (Type AT)		Max. Working Pressure (Type S)		Min Bend Radius	Weight
				Min	Max	Min	Max	psi	bar	psi	bar	mm	kg/m
MR1-3	5	3/16	-3	4.6	5.4	8.9	10.1	3045	210	3625	250	90	0.2
MR1-4	6.3	1/4	-4	6.2	7	10.6	11.7	2780	192	3260	225	100	0.25
MR1-5	8	5/16	-5	7.7	8.5	12.1	13.3	2540	175	3120	215	115	0.31
MR1-6	10	3/8	-6	9.3	10.1	14.5	15.7	2280	157	2610	180	125	0.36
MR1-8	12.5	1/2	-8	12.3	13.5	17.5	19	2030	140	2320	160	180	0.45
MR1-10	16	5/8	-10	15.5	16.7	20.6	22.2	1520	105	1885	130	205	0.52
MR1-12	19	3/4	-12	18.6	19.8	24.6	26.2	1260	87	1520	105	240	0.65
MR1-16	25	1	-16	25	26.4	32.5	34.1	1015	70	1260	87	300	0.91
MR1-20	31.5	1-1/4	-20	31.4	33	39.3	41.7	620	43	900	62	420	1.3
MR1-24	38	1-1/2	-24	37.7	39.3	45.6	48	510	35	725	50	500	1.7
MR1-32	51	2	-32	50.4	52	58.7	61.9	380	26	580	40	630	2

Notes:

1. 1MPa=10bar=145psi;
2. Bending radius measured on the inside of the bend;
3. SAE Dash Size equals to hose I.D. in 1/16's of an inch.